Surtreat site icon

SURTREAT TPS IV – Concrete, Brick, Stone and Mortar

SURTREAT TPS IV is a hardener and surface protection agent for porous cement based concrete, block, mortar as well as stone and brick. SURTREAT TPS IV is a penetrating material. It is designed to combine with the substrate without leaving any film or residue. SURTREAT TPS IV fills the pores and cracks to reduce porosity, increase concrete strength, and buffer pH. Additionally SURTREAT TPS IV protects concrete surfaces from acid, chloride, environmental and alkali attack, thereby extending the service life of the structure.


Our formula makes for an solution for structures old and new. With proven laboratory and site performance, our product can be applied to a variety of surfaces. The formula is also environmentally friendly, breathable, extremely durable, and penetrates easily. Once applied, it can not be peeled or scratched off of the original surface and can be painted, coated, or overlaid as needed.

Special Features

SURTREAT TPS IV increases surface hardness and strength. Appropriate for areas of heavy traffic such as loading zones. For use in chemically aggressive environments where acid, salt, or oil/hydraulic liquid contamination and erosion is confirmed or expected. Often is used in combination with SURTREAT TPS II and SURTREAT REPEL WB to provide a full spectrum protection.


5 gallon pail and 55 gallon drum.


Caution and Safety

Handling: SURTREAT TPS IV is to be applied by professional contractors only. All applicators should wear OSHA and NIOSH recommended protective equipment. Do not use or dilute the product in closed areas without adequate ventilation. Immediately close the container after removal of the solution. Avoid contact with skin, eyes and clothing. Do not smoke, eat or drink during application. Wash thoroughly after handling. Keep out of reach of children. Do not inhale or ingest or modify the solution. Refer to MSDS.

Clean Up: In case of spills or leaks, wear suitable protective equipment. Contain spill and collect with absorbent material or process and transfer to a suitable container, ventilate area. Avoid contact. Dispose of in accordance with current, applicable local, state and federal regulations.

Precautions: KEEP OUT OF REACH OF CHILDREN. DO NOT SWALLOW. Use with adequate ventilation. Avoid mist and direct contact with eyes, skin and clothing. Wear suitable protective goggles, gloves, and clothing. In case of insufficient ventilation, wear suitable respiratory equipment. If you feel ill, seek medical advice. Wash clothing prior to re-use.

Physical / Chemical Characteristics 

Boiling point: 212F
Specific gravity: 1.16
Flashpoint: none pH: 12(+/-.5)
Appearance and odor: clear liquid with mild chemical smell
Shelf life: 24 months in an unsealed factory container
Storage: protect from freezing

Where To Use

Reinforced, precast, prestressed, or post-tensioned concrete structures. To date SURTREAT TPS IV has successfully been used on bridges, roadways, runways, various buildings including stadiums, condominiums and office, parking garages, marine structures, industrial plants including food processing and chemical manufacturing, at nuclear facilities, NASA, military installations and mines.

Application Procedure 

Surface preparation: Prior to applying SURTREATTPS IV the surface must be clean, sound, and reasonably dry.

Application: SURTREAT TPS IV is applied by roller, brush or spray onto the concrete surface. When spraying, use conventional airless spray system or hand-pressure equipment. A minimum of two applications is usually required. Apply liberally until substrate is saturated. Spread with squeegee, brush or roller until adsorbed. Waiting time between applications, will vary depending on environmental conditions and absorbency of substrate, is typically one hour. When applying prior to installation of a repair mortar, concrete overlay, coating or membrane, care must be taken to remove any SURTREAT TPS IV residue before the mortar or concrete is applied. This can be achieved by rinsing with water, pressure washing or grit blasting. After application, allow substrate to dry before applying coating or membrane.

Distribution rate should be about 120-150 sf/gal. It can be adjusted depending on project requirements.


  • Minimum ambient temperature and substrate temperature of 35F. Do not apply when temperature is expected to fall below freezing within twelve hours.
  • SURTREAT TPS IV will not penetrate sealers, coatings, paints, and membranes.
  • Avoid contact with glass, aluminum and painted surfaces – may cause permanent spotting.




437 Grant Street, Frick Building Suite 1210, Pittsburgh, PA 15219 USA