SURTREAT TPS XII – Concrete, Brick, Stone and Mortar
Surtreat TPS XII is an organic, surface applied corrosion inhibitor for use on hardened concrete. It is designed to protect reinforcing steel in concrete from corrosion by penetrating the concrete surface and migrating, in liquid and vapor form, to the reinforcing steel. SURTREAT TPS XII forms a passivating film on the steel surface which provides protection from the corrosion process, thereby extending the service life of the structure.
Our formula makes for an outstanding one part corrosion inhibitor for hardened steel reinforced concrete – old and new. With proven laboratory and site performance, our product can be applied to a variety of surfaces. The formula is also environmentally friendly, breathable, extremely durable, and penetrates easily. Once applied, it can not be peeled or scratched off of the original surface and can be painted, coated, or overlaid as needed.
SURTREAT TPS XII is a vapor-phase corrosion inhibitor (VCI) for concrete. It penetrates easily as gas and affects steel properties at both the anodic and cathodic sites. Due to high penetrative ability minimal or no surface removal is required for the SURTREAT TPS XII to be highly effective at the rebar depth. SURTREAT TPS XII is especially effective in areas of corrosion “hot spots” and instances of chloride induced corrosion. For maximum corrosion protection SURTREAT TPS XII is recommended for use in combination with SURTREAT TPS II.
5 gallon pail and 55 gallon drum.
Caution and Safety
Handling: SURTREAT TPS XII is to be applied by professional contractors only. All applicators should wear OSHA and NIOSH recommended protective equipment. Do not use or dilute the product in closed areas without adequate ventilation. Immediately close the container after removal of the solution. Avoid contact with skin, eyes and clothing. Do not smoke, eat or drink during application. Wash thoroughly after handling. Keep out of reach of children. Do not inhale or ingest or modify the solution. Refer to MSDS.
Clean Up: In case of spills or leaks, wear suitable protective equipment. Contain spill and collect with absorbent material or process and transfer to a suitable container, ventilate area. Avoid contact. Dispose of in accordance with current, applicable local, state and federal regulations.
Precautions: KEEP OUT OF REACH OF CHILDREN. DO NOT SWALLOW. Use with adequate ventilation. Avoid mist and direct contact with eyes, skin and clothing. Wear suitable protective goggles, gloves, and clothing. In case of insufficient ventilation, wear suitable respiratory equipment. If you feel ill, seek medical advice. Wash clothing prior to re-use.
Physical / Chemical Characteristics
Boiling point: 212F
Specific gravity: 1.03
Flashpoint: > 212F pH: 8 – 8.5
Appearance and odor: amber liquid with chemical smell
Shelf life: 24 months in an unsealed factory container
Storage: protect from freezing
Where To Use
Reinforced, precast, prestressed, or post-tensioned concrete structures.
To date SURTREAT TPS XII has successfully been used on bridges, roadways, runways, various buildings including stadiums, condominiums and office, parking garages, marine structures, industrial plants including food processing and chemical manufacturing, at nuclear facilities, NASA, military installations and mines.
Surface preparation: Prior to applying SURTREAT TPS XII the surface must be clean, sound, and reasonably dry.
Application: SURTREAT TPS XII is applied by roller, brush or spray onto the concrete surface. When spraying, use conventional airless spray system or hand-pressure equipment. A minimum of two applications is usually required. Apply liberally until substrate is saturated. Spread with squeegee, brush or roller until adsorbed. Waiting time between applications, will vary depending on environmental conditions and absorbency of substrate, is typically one hour. When applying prior to installation of a repair mortar, concrete overlay, coating or membrane, care must be taken to remove any SURTREAT TPS XII residue before the mortar or concrete is applied. This can be achieved by rinsing with water, pressure washing or grit blasting. After application, allow substrate to dry before applying coating or membrane.
Distribution rate should be about 100-120 sf/gal. It can be adjusted depending on project requirements.
- Minimum ambient temperature and substrate temperature of 35F. Do not apply when temperature is expected to fall below freezing within twelve hours.
- SURTREAT TPS XII will not penetrate sealers, coatings, paints, and membranes.
- When used indoors caution should be taken to provide adequate ventilation and additional protective gear such as respirators should be worn by the applicators.